![]() After some time, on the bottom, it'll state: "Press 1 to continue"ĥ)You will be taken to some text saying " The test results are in:" and "The Homebrew Channel: Can be installed", "BootMii: Can be installed". It will stay on this screen for a good 20 seconds, just be patient. <-įor right now, I'm going to guess you are already hacked and have HBC installed(I'll go over unmodded Wii's near the end)ġ)Go to and Download HackMii Installer v1.2.Ģ)Place the HackMii folder in your apps folder you use for HBCģ)Go to HBC and there should be an app without a logo, just blank, but when you go to open it, it should be titled HackMii.Ĥ)As soon as you open it, an image should pop up stating "THIS SOFTWARE MUST NOT BE SOLD" blah blah blah, some more scammed mumbo jumbo. > Try BootMii if Priiloader is not working for you. Now you no longer need a Wiimote to start booting up your ISO files, as a GC controller (d-pad) can navigate the Homebrew Channel.Īpparently you can have it boot straight to a Homebrew app if you want, but I've never done this. Then turn on Wii normally and it should now boot straight to the Homebrew Channel. hold those buttons until a white Priioader menu appears.ĩ) Go to the "Settings" menu at the bottom.ġ0) At the top, change "Autoboot" to "Homebrew Channel"ġ2) Hold Power Button to turn off Wii. ![]() Press A on GC controller (or whatever it says for Wiimote) to start the install.ħ) When it is done, exit back to the Homebrew Channel and then hold the power button on your Wii to turn it off.Ĩ) Turn Wii back on by holding the Power Button & the Reset Button, right below the power button, at the same time. Don't run Miimaker channel (miimaker channel is used only for Homebrew Launcher 1.1) Have your Wii hacked so that the Homebrew Channel is available.Ĥ) From the downloaded and unzipped files, Copy the "priiloader" folder, which is inside the "apps" folder, and paste it into the "apps" folder that should be on the root of your SD card.ĥ)Insert SD Card into Wii -> Boot up Wii -> go to Homebrew Channel -> load Priiloader.Ħ) Wait a second as it sets up some files. You can run the Homebrew Launcher channel again if you want to run homebrew again. Usually, homebrew are released for both normal and channel version, just use the correct one based on the HBL you setup.ĥ. Note2: if you have Haxchi, you don't need the Channel version, you can use the "Homebrew version with haxchi" section from above, unless the homebrew you want to run is specifically compiled for the channel version. Note1: you don't need to run haxchi or Mocha a second time before launching the channel version a second time, the CFW is still in memory until you shutdown your console. To launch the installed Homebrew Launcher channel, run your CFW once (Mocha sysmenu patcher, or Haxchi sysmenu patcher) if you just powered ON your console, or if you use CBHC you don't have to run anything first, and select the homebrew launcher from your WiiU home menu. fw.img is an old and deprecated CFW method.Ĥ. Just use Mocha instead! you'll know you have the correct custom firmware. If you don't use the correct fw.img, you will get an installation error! *To install the channel version you need a SPECIFIC fw.img, do not use an existing and previously compiled fw.img, you need to get the newest Dimok's branch (The custom firmware needs to be from or newer) and compile with "make cfw" to get the proper fw.img for sysNAND or "make redNAND" to get a proper fw.img for redNAND with The homebrew Launcher compatibility. Use WUP installer (any version) or WUP Server with install() command to install the Homebrew channel package on a signature patched firmware. run a custom firmware (Mocha or an old Dimok's IOSUHax fw.img*, or haxchi or CBHC).ģ. Download and extract the channel version to sd:/install/ (put your. Run haxchi without pressing any button and, if you didn't change the config.txt, the homebrew launcher will be launched by default.ġ. The 551hbl.mp4 and the 532 codebin are provided here to update the hosted website exploit. The install steps are similar, but only updated website exploit can launch the rpx version. The homebrew channel is also available in rpx format, which is the native executable format of the WiiU. To run Homebrew Launcher again, just run miimaker channel instead of launching the browserhax exploit a second time, or it will freeze the console. ![]() On first launch and until you shutdown the console or launch WiiU settings app, HBL is replacing Miimaker channel. SD:/wiiu/apps/homebrew_launcher/homebrew_launcher.elf Download and extract the wiiu folder from the release package to the root of your SD card. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |